Real DES-1241 Exam PDF Test Engine Practice Test Questions
EMC DES-1241 Real 2022 Braindumps Mock Exam Dumps
NEW QUESTION 29
While on-site installing a Dell EMC PowerStore T system, the node A embedded module management Ethernet port link LED is off. What does this indicate?
- A. No network connection is established
- B. Network connection is established
- C. Port speed is 1 GB/s
- D. Port speed is 10 GB/s
Answer: A
NEW QUESTION 30
Under which condition does the Dell EMC PowerStore equipment in the rack require additional stability?
- A. Unstable environments
- B. Low temperatures
- C. High temperatures
- D. Unstable humidity
Answer: A
NEW QUESTION 31
A Storage Administrator notices a Critical alert present in Dell EMC PowerStore Manager relating to data integrity. What action within the alert details slide-out panel is helpful in troubleshooting the problem?
- A. Access the Repair Flow link to schedule a support engagement
- B. Examine Notifications to obtain a list of corrective actions
- C. Re-engage support through previous listed Related Events
- D. Select the Gather Support Materials from Service and Support
Answer: B
NEW QUESTION 32
For what is the "svc_container_mgmt status CP" command used?
- A. Resets the Data Path root access
- B. Clears the Control Path audit log
- C. Checks the status of the Control Path
- D. Checks the status of the Data Path
Answer: C
NEW QUESTION 33
How many nodes are in the base enclosure?
- A. 2 nodes configured as Active-Active
- B. 1 node with high availability enabled
- C. 1 node with duel connectivity
- D. 2 nodes configured as Active-Standby
Answer: A
Explanation:
Reference:
https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-hwg/base-enclosure- component-overview?guid=guid-7914a554-6943-402e-bd38-3e893163657e&lang=en-us
NEW QUESTION 34
What is the maximum number of expansion enclosures that a single Dell EMC PowerStore appliance supports?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 35
What describes Dell EMC PowerStore heat dissipation?
- A. Higher model numbered systems have lower heat dissipation specifications than lower model numbered systems
- B. X systems have higher heat dissipation specifics than T systems
- C. T systems have higher heat dissipation specifics than X systems
- D. Lower model numbered systems have lower heat dissipation specifications than higher model numbered systems
Answer: B
NEW QUESTION 36
When connecting a PowerStore base enclosure to 2 expansion enclosures, match the base SAS ports in column A to their corresponding expansion LCC ports in column B.
Answer:
Explanation:
Reference:
https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-1000/pwrstr-isg/cable-the-base-enclosure-to- the-expansion-enclosure?guid=guid-d68d049f-2b77-489f-b1ab-553f4f3de8aa&lang=en-us
NEW QUESTION 37
What is the reason for the best practice of leaving 2 Us of space at the bottom of the rack when racking Dell EMC PowerStore systems?
- A. Leave clearance for wheel roll
- B. Leave room for serviceability
- C. Provide better rack stability
- D. Provide cooling air intake
Answer: B
NEW QUESTION 38
How can the PUHC health check results be viewed?
- A. From management DB
- B. From syslog server
- C. In Details of Appliances and Nodes
- D. By accessing the Swagger UI
Answer: D
NEW QUESTION 39
What describes Dell EMC PowerStore X front-end cabling?
- A. Management and discovery use the same cables and connections as storage
- B. Uses VLTi data switch interconnectivity to support vMotion networks
- C. Uses internal VMware virtual switching and does not require a management network
- D. Storage and management use the same LACP bonded cable connection
Answer: A
Explanation:
"For PowerStore T model appliances, the individual ports within the system bond could be running in active/active mode or active/passive mode. This state depends on whether Link Aggregation Control Protocol (LACP) has been configured on the network switches. To ensure best resiliency and network performance, it is recommended to enable LACP on the network. For more information about configuring LACP for a PowerStore T model appliance, see the document PowerStore Guide for PowerStore T Models on the PowerStore Info Hub. For PowerStore X model appliances, there is no system bond and no LACP configuration is needed because the link aggregation and failover is handled by the virtual switches within the VMware hypervisor. "
NEW QUESTION 40
What is the maximum number of base enclosures in a cluster when planning a Dell EMC PowerStore T installation?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 41
Refer to the exhibit.
What is the result of the network configuration show for a Dell EMC PowerStore T node A management port?
- A. VLAN 1 passes untagged traffic, VLAN 1501 passes tagged traffic
- B. VLAN 1 and VLAN 1501 pass untagged traffic
- C. VLAN 1 passes tagged traffic, VLAN 1501 passes untagged traffic
- D. VLAN 1 and VLAN 1501 pass tagged traffic
Answer: A
NEW QUESTION 42
How is a defective DIMM displayed in Dell EMC PowerStore Manager?
- A. Orange with a faulted state
- B. Blue with a faulted state
- C. Blue with an empty state
- D. Orange with an empty state
Answer: A
NEW QUESTION 43
What does the output of the PSTCLI command "nas_server show" display from a Dell EMC PowerStore T?
- A. Memory utilization and thread count for NFS NAS servers
- B. SIDs of SMB NAS servers joined to the AD Domain
- C. If NAS servers are present if they are either NFS or Licensed
- D. If NAS servers are present and if they are either Started or Degraded
Answer: C
NEW QUESTION 44
Refer to the exhibit.
What is the result of the network configuration shown for a Dell EMC PowerStore T?
- A. Ports 1/1/55 and 1/1/56 are added to the VLTi domain
- B. Interfaces are configured for PowerStore discovery traffic
- C. Ports 1/1/55 and 1/1/56 are added to a new LACP domain
- D. Interfaces are configured for remote replication traffic
Answer: B
NEW QUESTION 45
......
Prepare For The DES-1241 Question Papers In Advance: https://guidetorrent.dumpstorrent.com/DES-1241-exam-prep.html