A fully updated 2023 HPE0-S60 Exam Dumps exam guide from training expert DumpsTorrent
Provides complete coverage of every objective on exam and exam preparation HPE0-S60
NEW QUESTION # 42
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard licenses for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options Which statement about this proposal is true?
- A. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50GD/S ILM
- B. vSphere Standard licenses should be replaced with Enterprise Pius licenses to enable requested features
- C. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drive.
- D. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup
Answer: B
NEW QUESTION # 43
Your customer reports mat an external FC boot volume for Windows server is visible four times in the Disk Management 1 online and 3 offline.
What should you do to resolve this issue?
- A. Disable deduplication for this volume at the array level
- B. Remove the offline disks using array management tools
- C. Remove the offline disks using Windows Disk Management
- D. Install and configure MPIO on me Windows system
Answer: D
NEW QUESTION # 44
Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.
Which statement regarding this setup is true?
- A. Interconnect modules that provide SAS connectivity should be moved to the third fabric
- B. Each compute node must have at least 768GB of memory installed
- C. Compute nodes must have a second CPU installed to access the second fabric.
- D. Each interconnect module in each fabric must be properly licensed in HPE OneView
Answer: B
NEW QUESTION # 45
After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.
Answer:
Explanation:
NEW QUESTION # 46
Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?
- A. The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.
- B. The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.
- C. The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.
- D. The customer can add a new logical enclosure to an existing setup once all required licenses are added lo HPE OneView and associated with the new frames.
Answer: B
NEW QUESTION # 47
Your customer manages HPE Synergy using HPE OneView. For one of its projects, the company purchased 50 HPE.
ProLiant DK385 Gen10 Plus v2. They plan to manage the new systems using HPE OneView as well.
What should the customer do to manage rack system using HPE OneView?
- A. Deploy HPE OneView Global Dashboard and add the rack systems there, as AMD systems are not directly in HPE OneView.
- B. connect the rack system to an IPDU and add the IPDU to the HPE. OneView instance that is used for HPE synergy management.
- C. Deploy an HPE OneView virtual appliance, and, after configuration, use it to manage only the rack systems.
- D. add the rack system to the HPE OneView instance used to manage HPE Synergy to centralize management of all systems.
Answer: C
NEW QUESTION # 48
Your customer plans to deploy VMware vSAN using D3940 Storage Modules.
Which statement about this solution is true?
- A. The 12Gb SAS modules required for D3940 connectivity can only be installed in the first fabric.
- B. For VMware vSAN deployment, all drives in the D3940 storage modules must be SSD drives.
- C. To use the storage controller that will access D3940 storage modules, a second CPU must be installed.
- D. All drives in the D3940 storage modules must formulate a single logical drive with RAID5 configured
Answer: A
NEW QUESTION # 49
Your customer has the following HPE Synergy setup
- 3 HPE Synergy 12000 Frames
- 4 HPE Virtual Connect SE 100 Gb F32 Modules
- 2 HPE Synergy 50 GO Interconnect Link Modules
- 36 HPE Synergy 480 Gen10 Plus compute modules
- 2 HPE Composer 2 modules
Which statement about this setup is true?
- A. The customer can add one D3940 storage Module to each of the frames
- B. To manage all frames, the customer must buy two additional HPE Composer 2 modules
- C. The customer must buy 36 HPE OneView Advanced licenses to manage compute modules
- D. To use all compute nodes, the customer must create at least two logical enclosures
Answer: C
NEW QUESTION # 50
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex
280 They plan to manage new components using HPE OneView
What must be done to achieve this goal?
- A. The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView
- B. The customer must add a second Rack Management Controller for HPE Superdome Flex 280
- C. The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy
- D. The customer should deploy an HPE OneView appliance for HPE Superdome Flex management
Answer: B
NEW QUESTION # 51
You configured a vVoI datastore using HPE Storage integration Pack for VMware vCenter.
Which storage object should you check using SSMC to verify whether vVol datastore is configured property?
- A. Storage Container
- B. virtual Volume
- C. Virtual Volume Set
- D. App Volume Set
Answer: C
NEW QUESTION # 52
Your customer has the following HPE Synergy setup:
- 15 HPE Synergy 12000 frames with 50Gb connectivity to each server port
- 2 HPE Composer 2 modules
- 15 HPE D3940 Storage Modules, one per frame
- 2 HPE 12Gb SAS switches per frame
Which statement about this setup is true?
- A. To manage 15 frames, additional HPE Composers are required.
- B. If properly cabled, any compute node can access any HPE D3490 storage module
- C. The customer must create at least five logical enclosures for this setup.
- D. The customer can install up to 12 HPE Synergy 480 compute nodes per frame.
Answer: C
NEW QUESTION # 53
What is a restriction of using a RoCE network?
- A. It is by default configured as an untagged network and cannot be a part of a network set.
- B. It does not support Private VLAN and Multicast VLAN.
- C. It does not support smart link and private network features.
- D. it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
Answer: A
NEW QUESTION # 54
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A. An additional license is required to change the enclosure count
- B. For an uplink set, ports from different modules can be selected
- C. Both modules are located in different frames for redundancy
- D. interconnect modules are installed in interconnect bays 1 and 4
Answer: A
NEW QUESTION # 55
Click the option that will allow you to change the ESXI image used In an OS Deployment Plan.
Answer:
Explanation:
NEW QUESTION # 56
A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?
- A. HPE Synergy 12 Gb SAS Connection Module
- B. Brocade 32GB Fibre Channel Switch Module for HPE Synergy
- C. HPE virtual Connect SE 32 Gb FC Module for Synergy
- D. HPE Virtual Connect SE 100 Gb F32 Module tor Synergy
Answer: D
NEW QUESTION # 57
What is a limitation when creating a server profile?
- A. Administrator cannot define more than 8 connections within a server profile
- B. BIOS settings can be changed only when UEFI optimized is selected as boot mode
- C. ILO management is limited to the integration with Active Directory or LDAP
- D. It is not possible to create shared volumes on demand through a server profile
Answer: C
NEW QUESTION # 58
Your customer uses HPE OneView to manage their HPE Synergy environment. They plan to use it to manage a new set equipment that includes.
- 20 HPE ProLiant DL365 Gen10 Plus servers
- 20 HPE ProLiant DL380 Gen10 Plus servers
- 5 HPE Primera 650
- 5 HPE MSA 2062 Storage Array
Which statements about now OneView will work with this new equipment are true? (Select two)
- A. HPE MSA 2062 Storage Array is not supported in HPE OneView
- B. HPE ProLiant DL380 Gen10 Plus servers have an HPE OneView license included
- C. HPE ProLiant DL365 Gen10 Plus servers are not supported in HPE OneView
- D. HPE OneView replaces array management tools for both types of array
- E. HPE Primera 650 can be managed using HPE OneView.
Answer: B
NEW QUESTION # 59
Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.
Answer:
Explanation:
NEW QUESTION # 60
An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays Where should you start the troubleshooting process?
- A. At the iLO interface to verify whether the SSO certificate is removed from an iLO.
- B. At HPE OneView Interface to verify whether the iLO processor is disabled
- C. At HPE OneView Interface to verify whether the server is In the maintenance mode
- D. At the iLO interface to verify whether the ILO Advanced license is properly applied
Answer: D
NEW QUESTION # 61
Your customer wants to add dedicated Fibre Channel connectivity to the HPE Synergy frame running HPE Synergy 480 Gen10 compute modules, each with one CPU socket populated Currently they use two 12 Gb SAS switches and two HPE Virtual Connect SE 100Gb F32 Modules for HPE Synergy installed in third fabric.
What must be done to enable dedicated FC connectivity for this HPE Synergy frame?
- A. For VC-FC modules, all of server facing ports must be property licensed.
- B. A second CPU must be installed for all HPE Synergy 480 Gen10 compute nodes.
- C. For Brocade switches, a logical interconnect group must be created in HPE OneView.
- D. SAS switches must be moved to second fabric and FC modules Installed in the first one.
Answer: D
NEW QUESTION # 62
Match each HPE OneView network type with its definition.
Answer:
Explanation:
NEW QUESTION # 63
Refer to the exhibit.
Which statement about this logical JBOD is true?
- A. After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done
- B. This logical JBOD can be presented to the compute nodes in a different frame.
- C. After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created
- D. This logical JBOD can be connected to multiple systems to formulate a snared datastore.
Answer: A
NEW QUESTION # 64
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)
- A. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
- B. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- C. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- D. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- E. Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
- F. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
Answer: B,C
NEW QUESTION # 65
......
HP HPE0-S60 exam aims to assess the candidate’s proficiency in implementing and configuring HPE compute solutions. It covers a wide range of topics, including HPE Synergy solutions, HPE ProLiant Gen10 solutions, HPE BladeSystem solutions, and HPE Apollo solutions. HPE0-S60 exam also tests the candidate’s knowledge of HPE OneView, HPE iLO, and HPE Intelligent Provisioning. By passing HPE0-S60 exam, the candidate will gain a valuable credential that demonstrates their expertise in HPE compute solutions.
Tested Material Used To HPE0-S60: https://guidetorrent.dumpstorrent.com/HPE0-S60-exam-prep.html